Сonnection to PC

Different network connections are possible. The main configurations are given below. The diagnostic device ScanDoc can work in a wired or wireless net.

Version with Ethernet

ethernet1
ethernet2

Ethernet is the most reliable and noise-protected connection. But it is less convenient, than WLAN.

Attention!
It is strongly recommended to use Ethernet for control device programming.

If you have already Ethernet network 192.168.1.ххх or no network

  1. Switch on the device and connect it to your computer by Ethernet cable.
  2. Set IP-address in Windows XP or Windows 7.
  3. Start the communication test.

If you have already Ethernet network (not 192.168.1.ххх) and you need to change IP-address in ScanDoc

  1. Switch on the device and connect it to your computer by Ethernet cable.
  2. Set IP-address in Windows XP or Windows 7.
  3. Change IP-address in ScanDoc.
  4. Set your IP-address in Windows XP or Windows 7.
  5. Start the communication test.

Version with WLAN without access point

wi-fi3

This is the easiest way of connection.

  1. Switch on the device.
  2. Push the button Wi-Fi on the side panel of device. ScanDoc will be connected to internal WLAN module.
  3. Connect to Quantex wireless networ.
  4. Put ScanDoc Wi-Fi unit into AP mode.

Note:
This version is set by default.

Version with WLAN with access point

wi-fi1
wi-fi2

This scheme is used if you need to work with several devices by wireless connection or you have already
wireless network, set according to your requirements. In this case it can be necessary to change IP address of the diagnostic scanner ScanDoc.
In this scheme: computer is a WLAN access point (or WLAN router) in Access Point mode (AP), Scandoc WLAN unit in AP Client mode.

If you have already WLAN network (not 192.168.1.ххх) and you need to change IP-address in ScanDoc

  1. Connect ScanDoc by Ethernet cable.
  2. Change IP-address in the device.
  3. Push the button Wi-Fi on the side panel of device. ScanDoc will be connected to internal WLAN module.
  4. Put ScanDoc Wi-Fi unit into AP Client mode.
  5. Start the communication test.

If you have already WLAN network 192.168.1.ххх or no network

  1. Switch on the device.
  2. Push the button Wi-Fi on the side panel of device. ScanDoc will be connected to internal WLAN module.
  3. Put ScanDoc Wi-Fi unit into AP Client mode.
  4. Start the communication test.

If you have new unconfigured access point

  1. Switch on the device.
  2. Push the button Wi-Fi on the device. ScanDoc will be connected to internal WLAN module.
  3. Puit your access point in АP mode.
  4. Put ScanDoc Wi-Fi unit into AP Client mode.
  5. Start the communication test.

 

IP address settings in Windows 7/Vista

Push Start in the left lower corner in Windows and choose the menu point «Control Panel» > «Network and Internet» > «View network status and tasks».
ethernetwin7 1 eng

In the appeared window choose «Change adapter settings».
ethernetwin7 2 eng

Choose network connection with ScanDoc connected to it, then push the right button of the mouse on the icon and choose «Properties» in the drop down window.
ethernetwin7 3 eng

In the new window put cursor on «Internet protocol version 4» and click Properties.
ethernetwin7 4 eng

Set IP-address 192.168.1.50 and subnet mask 255.255.255.0 These parameters are spread to the network card of PC. Instead number 50 of IP-address you can set any number from 1 to 254, except 3. ScanDoc IP-address is 192.168.1.3 by default.
ethernetwin7 5 eng

IP address setting in Windows XP

Push Start in the left lower corner in Windows and choose «Control Panel» > «Network and Internet Connections».
ethernetwinxp 1

Choose «Network connections».
ethernetwinxp 2

Choose network connection with ScanDoc connected to it, push the right button of the mouse on the icon and choose Properties in the drop down menu.
ethernetwinxp 3

In the new window put cursor on «Internet Protocol (TCP/IP)» and click Properties.
ethernetwinxp 4

Set IP-address 192.168.1.50 and subnet mask 255.255.255.0 These parameters are spread to the network card of PC. Instead number 50 of IP-address you can set any number from 1 to 254, except 3. ScanDoc IP-address is 192.168.1.3 by default.
ethernetwinxp 5

ScanDoc IP address change

1. Launch ScanDoc software, open settings menu and select the option Change IP.
2. In the new window put the current and new IP-address. ScanDoc IP-address is 192.168.1.3 by default.

editip

 

ScanDoc  WLAN-unit setting in AP Client mode

Attention!
Disconnect all wired network connections before setting of ScanDoc WLAN-unit.

ScanDoc  WLAN-unit setting can be performed only via wireless connection. Connect to ScanDoc wireless network. Open your internet browser, go to the following address http://192.168.1.250. In the apeared window enter user name admin, password admin and push the button OK.

apclient1

If all connectors in the field «Ethernet Port Status» are white, push the button Wi-Fi on the side panel of ScanDoc.

apclient2

In Operation Mode menu select «AP Client» and push the button Save.

apclient3

Attention!
After you save settings ScanDoc WLAN-unit will change IP-address and will be available at address http://192.168.16.254.

Please take a moment to let the new settings take effect.

Go to the following address - http://192.168.16.254.
In Internet Settings menu select WAN.
Change the following settings:

  1. WAN Connection Type STATIC (fixed IP).
  2. IP Address 192.168.1.250.
  3. Subnet Mask 255.255.255.0.
  4. Default Gateway clear the field.

Push the button Save.

apclient4

In the Wireless Settings menu select «AP Client».

apclient5

Click the "Search AP" button. In the appeared window choose access point required.

apclient6

Push the button Connect.

Change the following settings:

  1. Operation Mode Multi-Bridge Mode.
  2. Security Mode WPA2-PSK (must coincide with settings of the main access point).
  3. Encryption Type AES (must coincide with settings of the main access point).
  4. Pass Phrase (must coincide with the password of the main access point).

Push the button Apply.

apclient7

Attention!
Values in the fields «MAC Address (Optional)» and «Pass Phrase» are given as an example!

If everything is done correctly, ScanDoc WLAN-unit will connect to main access point.
ScanDoc WLAN-unit is available at the following adress -  http://192.168.1.250.

It is recommended to change security settings of ScanDoc WLAN-unit to avert unauthorized access to Quantex wireless network.

Go to the following address - http://192.168.1.250. In the «Wireless Settings» menu select «Security».
Change the following settings:

  1. Security Mode WPA2-PSK.
  2. WPA Algorithms AES.
  3. Pass Phrase preferred password.

Push the button Save.

apclient8

Attention!
Value in the field Pass Phrase is given as an example!

ScanDoc WLAN-unit is completely configured and ready to work in AP Client mode. ScanDoc software can run both on desktop computers and notebooks via wired or wireless connection to access point.
Direct connection to Quantex wireless network is possible, but isn't used.

Note:
If you turn off and then turn on ScanDoc during the work, no connection with ScanDoc (IP-address 192.168.1.3) is possible.

There are two ways to recover the connection:

  1. Disconnect and connect the appropriate wired or wireless network connection again.
  2. Restart your conputer.

ScanDoc  WLAN-unit setting in AP mode

After factory reset  ScanDoc WLAN-unit works in AP mode.

It is recommended to change security settings of wireless connection to avert unauthorized access to ScanDoc WLAN-unit.
In the «Wireless Settings» menu select «Security».
Change the following settings:

  1. Security Mode WPA2-PSK.
  2. WPA Algorithms AES.
  3. Pass Phrase preferred password.

Push the button Save.

ap1

Attention!
Values in the field Pass Phrase is given as an example!

ScanDoc WLAN-unit is completely configured and ready to work in AP mode.

Factory reset of Scandoc WLAN-unit

  1. Switch off the device.
  2. Disconnect the main cable.
  3. Connect the test adapter, supplied with ScanDoc.
  4. Switch on the device.
  5. Wait 20 sec (red LED must beextinguished).
  6. Switch off the device.
  7. Disconnect the test adapter.

Example of ScanDoc  WLAN-unit setting in AP mode

Attention!
This access poit has only one wire Ethernet-connection.

Use Ethernet-connection for D-Link DWL-2100AP setting.
Settings of D-Link DWL-2100AP are available by address http://192.168.0.50.

  1. IP address 192.168.0.2.
  2. SubMask 255.255.255.0.

Open your internet browser and go to the following address - http://192.168.0.50.
Enter user name admin and push OK.

dlink1
Push the button Wireless.

dlink2

It is recommended to use encryption to avert unauthorized access to wireless connection. Select Authentication WPA2-PSK and Cipher Type AES.
It is necessary to select one of frequency channels from 1 to 13.
Change the following settings:

  1. Channel at your option.
  2. Authentication WPA2-PSK.
  3. Cipher Type AES.
  4. PassPhrase preferred password.

dlink2

Push the button Apply and wait a moment. Log in and push the button LAN.
Change the following settings:

  1. IP address 192.168.1.100.
  2. Default gateway 192.168.1.1.

Push the button Apply.

dlink4

Attention!                                                                                                                                    After you save settings D-Link DWL-2100AP will change IP-address and will be available at address http://192.168.1.100.

To work with this address you need to set your wired connection in Windows as follows:

  1. IP-address 192.168.1.2 (manual).
  2. SubMask 255.255.255.0.

If other wireless clients (laptops, tablets, etc.) except ScanDoc will work with your wireless network, it is necessary to set DHCP server on the main access point D-Link DWL-2100AP.
Go to the address http://192.168.1.100, log in, select «Advanced», push the button DHCP Server and change the following settings:

  1. Function Enable/Disable Enable.
  2. IP Assigned From 192.168.1.10.
  3. The Range of Pool (1-255) 10.
  4. SubMask 255.255.255.0.
  5. Gateway 192.168.1.1.
  6. Lease Time (60 - 31536000 sec) 600.
  7. Status ON.

dlink5

Push the button Apply and wait a moment.

When required, set a password for access to D-Link DWL-2100AP settings.

Log in and select «Tools».
New Password preferred password.
Confirm New Password (confirm preferred password).

dlink6

Push the button Apply. Here D-Link DWL-2100AP setting is over.